Manufactured from premium quality polyethylene, safari snorkels are incredibly resilient and UV stable. Install one before your next trip and breathe easier knowing that your engine is protected by a safari snorkel.Air intake systems are a common first mod to many project cars. They are quick and simple to install while also enhancing the looks of your engine bay, the sounds of your engine, and the performance of your vehicle. At this point I attempted to remove the MAF which was held in place with two philips head screws.One of them would not come loose, so I left it in place. The "Deckplate Mod" does just that.The factory air box draws in fresh air via a tube (refer to the intake diagram, item #4) that is inside the passenger fender wall.This tube, which is like a snorkel, is connected to the airbox through a 90 degree angled elbow (item #7) so that the opening is facing the rear of the vehicle.The reason is so that during off-road excursions in which water is encountered, water will not be easily ingested as the intake faces rearward.The trade off with that design is that the 90 degree bend is restrictive and reduces power.Removing the elbow (item #7) allows air to enter the airbox more easily, and will increase horsepower.But then each time you go offroad you would need to re-insert the elbow which takes time.There is a better way, and it is known as the "Deckplate Mod".Basically you install a marine deckplate on the front of the airbox (item #1).I purchased a Beckson 4" screw-out all black deckplate, part # DP40-B.This can be purchased at most any local boating supply shop.The benefit of using the deckplate is so that when you do take the rig off-road you can spin on the deckplate cover and the air box is sealed water tight.Here is how I performed the installation:Use a 12mm socket on an extension bar to remove 3 bolts which hold down the box.Unscrew the clamp (item #12) holding the airbox to the flex tube (item #10) with a philips screwdriver.Using needle nose pliers, squeeze the clips that hold the mass air flow sensor (item #3) wire harness to the air box.The airbox will now lift out of the vehicle.Remove the air filter and set it aside.Unfortunately, all snorkels that I have found run along the windshield where I have fabricated light mounts and installed some 6” ProComp lights. I was in the market for a snorkel for my 1986 Toyota 4Runner. Insert the deckplate into the hole and mark the places to drill pilot holes for the 6 screws.Remove the deckplate and drill 6 pilot holes using a 1/8" drill bit.Remove the plastic bag which collected most of the material that resulted from cutting and drilling.Meticulously clean the interior of the air box, I used a vaccum to start off with.Place a bead of Sensor-Safe Silicon Sealant around the backside of the deckplate and insert it into the hole in the airbox.Secure the deckplate into place using 6 stainless steel #8 panhead screws that are 1/2" in legnth.Cut a piece of screen to approximately 5" in diameter.I took that number and subtracted 3” from it. I then fit a 90 degree angle inside the tube, and measured the distance between the PVC pipe and the firewall. I decided to DRY FIT all of the pieces to ensure my measurements. I cut the end piece off and reinstalled it so that it was standing straight up. Here is a list of things you will need:I started out by removing the inlet tube on the intake. I used 2” PVC tubing, the same type a Plumber would use for a job.I added another 45 degree angle and measured along the frame, to the point where I wanted it to turn up to the body. Also, I wanted to run the pipes very similar to the way the exhaust is running.Next, I measured the length from the 45 degree angle to the center of the space between the body and the frame, and cut the straight piece to length. Try to copy the angle of the header.Due to the three inch body lift I installed, I have just enough room to run the entire pipe between the body and the frame.
![]() This is where the hole is going to be. Now, off of that 90 degree angle, you need to attach another 90 degree angle so that it faces straight up to where the floor is. Due to the fact that I run my Runner with no top most of the year, I wanted the snorkel to peek up over the driver side of the roof.Again, cut that piece and fit a 90 degree angle to the end of that. You will need to know the length of the last piece of PVC pipe. If you did it right, you should be able to put that on while you are sitting in the back of the Runner.Before you go any further, you need to go Junkyard shopping to find the cap for your snorkel. I then took off the last 90 degree angle, and drilled a 2.5” hole from the top.Then I installed the last 90 degree angle again.Finally, you need to take that 2” to 2” adapter, and install it on the 90 degree angle. 025” hole in the center of the drawn circle. Prisma pro 2Then I went through and numbered them again on the inside rim. I went through and numbered all of the pieces from front to back, and disassembled. This is also a good place to install a screen filter.OK, so now you have dry fit the snorkel. I bought a rubber one so that it can be clamped. The only thing extra that I needed was a 2” to 3” adapter. 6Th Gen 4Runner Snorkel How To Install PvcMulti-tool on Wheels: 2017 Toyota 4Runner is the Everyday SUV That Lets You Explore When You Want, Where You Want Game Changer: 2019 Toyota TRD Pros Typify Ultimate Off-Road Performance Toyota Reimagines Marty Mcfly’s Dream Truck With 2016 Tacoma And if you’re air tight you’re definitely water tight!!! Good luck, and if you try this let me know your results.4Runner home made snorkel how to install pvc snorkel toyota Post navigation Dana 44 Axle Rebuild | ToyotaOffRoad. Robert Dumke on Hy-Steer Crossover Steering
0 Comments
Leave a Reply. |
AuthorBryan ArchivesCategories |